By Rob Leatham<\/a><\/p>\n Zeroing a pistol is considered an important first step after buying a new pistol. In today\u2019s article, champion shooter Rob Leatham explains his process for sighting in a handgun.<\/em><\/p>\n I<\/span> just got my grubby little hands on a few of the Springfield Armory\u00a01911 Range Officer\u00a0(RO) Elite pistols<\/a>. (Four to be exact.) And the one that grabbed my attention first was the Target Model. Probably not a big shock to those of you who know me as a competition shooter \u2014 this pistol was designed for someone just like me.<\/p>\n Any time I get a new gun, the first item on my to-do list is \u201czeroing.\u201d Zeroing is the process where I test for point of impact on a target and, if needed, make changes to the sights to cause that position to coincide with where I actually see (or think I see) the sights on the target.<\/p>\n A properly zeroed pistol means there is no variation between where I aim the gun and where the bullets hit. Now, to be honest, the term \u201czero\u201d means there is zero variation from sight to bullet impact. The reality, though, is\u00a0there is seldom a time when I use a gun that is 100 percent \u201czeroed.\u201d So for me, zeroed means \u201csighted in.\u201d<\/p>\n Since this is kind of confusing, I\u2019m going to document my zeroing-in process for your information and enjoyment. The RO\u00a0Elite Target<\/a> is fitted with my preferred fiber-optic front sight and a fully adjustable target rear sight \u2014 a perfect set up for quick and easy zeroing.<\/p>\n Several factors come into play that affect zeroing a pistol:<\/p>\n I\u2019m pretty efficient at zeroing my guns, as I\u2019ve been doing it for many decades. The more you do it, the better you\u2019ll get, too. Just follow these easy steps:<\/p>\n Gun and Ammo Initial Check:<\/strong> I first test how well the gun shoots out of the box and which ammo is the best or most suitable. This can be done in many ways, but I usually shoot standing, slow-fire with a two-handed grip at\u00a025 yards<\/strong>. (That\u2019s 75 feet on Top Shot!<\/em>)<\/p>\n POI Versus Point-of-Aim Check:<\/strong> With the selected load, I use a very specific aiming point in the center of the target. A square piece of 3\/4\u2033 black tape works well, but sometimes I just use a full-size USPSA target and shoot at the \u201cA\u201d imprinted in the middle of the body zone or the center of the smaller \u201chead\u201d of the target. I shoot five-shot groups to see where the gun\/ammo combination actually hits. When I establish whether it is dead on, high, low, left, or right, I start making basic adjustments to the rear sight.<\/p>\n How precisely I zero the pistol is based on the intended use of the gun. For many applications, it is at this point \u201cclose enough\u201d and nothing further needs to be done. My competition guns however are a different story. I want them perfect.<\/p>\n Windage Check:<\/strong> I prefer a given gun\/load combo to have as little lateral variation (windage) as possible. I never want the gun to impact left or right, so if it\u2019s off I make corrections until my hold is the variation, not the sights.<\/p>\n Elevation Check:<\/strong> As a general rule, I also do not like a gun to shoot low at the distance I am zeroing. Dead on to a little high is what I want to accomplish. Once I\u2019ve done this, I have a basic zero. Now it gets a little more complicated.<\/p>\n Specific Zeros:<\/strong> I next determine my \u201cpractical distance and accuracy\u201d requirements. I need a gun\u2019s elevation to be set for a specific POI\u00a0at a specific distance, based on the usage\/shooting discipline.\u00a0<\/p>\n I shoot slow-fire groups (standing) at the required distance and make fine adjustments to both windage and elevation until I\u2019m satisfied. Based on your skill level and ability to hold the gun stable, you may need to use a rested position. Since I notice variations in my POI between a rested and standing shooting position, I prefer to do my sighting in from the position\u00a0I most likely will use, which is standing. The only time I shoot from a stabilized position (i.e., sand bags on a table, seated, etc.) is when I\u2019m testing for accuracy, which is a completely different task. \u00a0<\/p>\n So now that you know what I require to zero the gun, how is it that you\u00a0specifically<\/em>\u00a0accomplish the task? Well, it\u2019s not always a simple process, because the type of gun and kind of sights determine the difficulty of the challenge.<\/p>\n A \u201cfixed sight\u201d<\/strong> gun usually allows for some windage adjustment by moving the rear sight, but elevation changes may require modification or replacement of the front or rear sight.\u00a0<\/p>\n An \u201cadjustable sight\u201d<\/strong> gun typically has a rear sight that allows you to move the \u201cblade\u201d in small increments (with a small screwdriver), usually with a \u201cclick\u201d you can hear or feel. Depending on the sight, this allows you to simply and easily make adjustments.<\/p>\n The shooter\u2019s skill level plays a very large part in the zeroing process. You must be able to shoot well enough to determine if the gun is zeroed. If you can\u2019t shoot a good enough group at the needed distance you may need to work on your shooting skills before you worry about adjusting the sights.<\/p>\n The good news is, most shooters will never see enough POI deviation at the closer distances they shoot for it to matter.<\/p>\n It should be relatively simple for experienced shooters to zero their concealed carry pistols, since the guns are typically expected to be employed at very close ranges. I can\u2019t imagine any out-of-the-box pistol deviating significantly in terms of POI from one to five yards, unless operator error interferes.<\/p>\n The four different XD-S<\/span>\u00a0pistols<\/a> I use for carry can hit a USPSA target in the center A-zone at 25 yards\u00a0straight from the factory, which highly\u00a0exceeds<\/em>\u00a0my requirement for a concealment pistol. \u00a0<\/p>\n My IPSC Classic Division competition 1911, on the other hand, needs to be much more precise at much greater distances, as many as 60 yards. I shoot non-standard ammunition loaded to a very specific velocity to keep recoil to a minimum. I prefer a 147-grain bullet with a special powder, because I like the feel of the combination and it\u2019s super accurate. \u00a0<\/p>\n The Springfield factory standard ammo for 9mm is 115-grain FMJ standard velocity ball, which shoots a much different POI than my special \u201ccheater\u201d loads. Because of this, I almost always need to adjust the sights when I get a new gun from the shop.<\/p>\n I make bold adjustments at first and then fine tune it with a click here and a click there until I\u2019m convinced that I can\u2019t get it any better. That\u2019s when it\u2019s nice to have a finely tuned and easily adjustable target sight on your pistol \u2014 just like the one on the RO\u00a0Elite Target<\/a>.<\/p>\n Each time you get a new gun or lot\/type of ammunition, be sure to follow a zeroing procedure. But do so based on your<\/em>\u00a0\u201cpractical distance and accuracy\u201d requirements. I bet you will end up not only more confident in your equipment, knowing exactly where your gun impacts, but hopefully also more confident in your skill level, as you should hopefully start to become a better shot.<\/p>\nSighting in a Handgun: First Step<\/h2>\n
More Than Meets the Eye<\/h2>\n
\n
\n
![\"zeroing](\"https:\/\/www.thearmorylife.com\/wp-content\/uploads\/2019\/09\/zeroing-a-pistol-with-sights-and-optic.webp\")
\n
![\"how](\"https:\/\/www.thearmorylife.com\/wp-content\/uploads\/2019\/09\/article-zero-pistol-1600x1065.jpg\")
Types of Sights<\/h2>\n
Variations of Skill<\/h2>\n
Discipline and Distance<\/h2>\n
Confidence and Improvement<\/h2>\n
Join the Discussion<\/span><\/h5>\n